multisio D6

Display
multisio F96-TFT

Storage center
multisio D6-ESBSDS-5DI6RO1DO

multisio D6 is the storage center for the modular system for signal recording and processing. Depending on the input or output type, a variety of functions can be selected.

The system is able to record the pulses from consumption meters and store them both as continuous meter data and as standard load protocols. Alternatively, a digital input can also be used to record the status (switching protocol) or the operating hours. Operating hours are available as continuous meter data and graphs. Compact expansion modules are available for a wide variety of signal forms (0 – 20 mA, 4 – 20 mA, 0 – 10 V, PT1000, current, power, etc.). Up to four expansion modules can be connected to each system control center using pre-assembled RJ45 cables.

Input and output configuration
Inputs	Outputs	Possible functions
5x digital	6x relays	Consumption recording
	1x DO	Status logging
	1x Display	Operating hours recording
		Pulse summation
		Relay circuit
		Analog value acquisition
		Temperature detection
		Heat quantity recording
		Electrical work

Input and output configuration

Inputs

Outputs

Possible functions

5x digital

6x relays

Consumption recording

1x DO

Status logging

1x Display

Operating hours recording

Pulse summation

Relay circuit

Analog value acquisition

Temperature detection

Heat quantity recording

Electrical work

Type:
multisio D6-ESBSDS-5DI6RO1DO-7	Article no. 20221
multisio D6-ESBSDS-5DI6RO1DO-7 NRTL	Article no. 24439

Type:

multisio D6-ESBSDS-5DI6RO1DO-7

Article no. 20221

multisio D6-ESBSDS-5DI6RO1DO-7 NRTL

Article no. 24439

Control and display elements:
Operation	Push button for reset and scan mode
Display	LED: 5 x input status, 1 x operating status, multisio F96-DS (LCD)

Control and display elements:

Operation

Push button for reset and scan mode

Display

LED: 5 x input status, 1 x operating status,
multisio F96-DS (LCD)

Storage:
Working, data and parameter memory	2 MB Flash
Program memory	512 kB Flash
Memory type	Ring buffer
Extreme values (max./min.)	The maximum values that have occurred since mains connection or manual extreme value deletion (drag indicator function) with date and time
Event event memory	Storage amount	1500 events with 1500 events with the date and time they occurred
Operational diary	Storage amount	500 entries with 500 entries with the date and time of their occurrence
Limit violation	Capture time	≥ 200 ms
Voltage dips in the measurement voltage	Capture time	≥ 20 ms; Threshold adjustable via PC, ≥ 20 ms; Threshold adjustable via PC, default after reset 85% of the nominal voltage (according to EN61000-4-30)

Storage:

Working, data and parameter memory

2 MB Flash

Program memory

512 kB Flash

Memory type

Ring buffer

Extreme values (max./min.)

The maximum values that have occurred since mains connection or manual extreme value deletion (drag indicator function) with date and time

Event event memory

Storage amount

1500 events with 1500 events with the date and time they occurred

Operational diary

Storage amount

500 entries with 500 entries with the date and time of their occurrence

Limit violation

Capture time

≥ 200 ms

Voltage dips in the measurement voltage

Capture time

≥ 20 ms; Threshold adjustable via PC, ≥ 20 ms; Threshold adjustable via PC, default after reset 85% of the nominal voltage (according to EN61000-4-30)

Power supply:
Power supply	US1: 100 – 240 V ±10% DC/50/60 Hz
Power consumption	22 VA

Power supply:

Power supply

US1: 100 – 240 V ±10% DC/50/60 Hz

Power consumption

22 VA

Hardware inputs:
Digital inputs	As pulse counter input 1 to 5	Digital input for potential-free contact, S0 – compatible, pulse length ≥ 30ms
As a status input	Digital input for potential-free contact, S0 – compatible, e.g. B. to synchronize the measurement period; Pulse length ≥ 250 ms
Voltage-voltage supply	27 V / 15 m A DC supplied internally

Hardware inputs:

Digital inputs

As pulse counter input 1 to 5

Digital input for potential-free contact, S0 – compatible, pulse length ≥ 30ms

As a status input

Digital input for potential-free contact, S0 – compatible, e.g. B. to synchronize the measurement period; Pulse length ≥ 250 ms

Voltage-voltage supply

27 V / 15 m A DC supplied internally

Electrical connection:
Connecting elements	Plug-in terminals
Max. permissible cross section of the connecting cables	2,5 mm²
Input power supply	Validation	max. 1A sluggish max. C2 Automatic machine Mains isolating device approved to UL/IEC
KBR eBus connection	Connecting material	For correct operation, only use shielded and twisted pair cables; e.g. I-Y(St)Y 2x2x0.8
Pulse inputs	Wiring & cables	pay attention to correct polarity!
Synchronous input	Wiring & cables	pay attention to correct polarity!
KBR eBus connection	via RS485	Terminal 90 (⊥) Terminal 91 (A) Terminal 92 (B)

Electrical connection:

Connecting elements

Plug-in terminals

Max. permissible cross section of the connecting cables

2,5 mm²

Input power supply

Validation

max. 1A sluggish
max. C2 Automatic machine
Mains isolating device approved to UL/IEC

KBR eBus connection

Connecting material

For correct operation, only use shielded and twisted pair cables; e.g. I-Y(St)Y 2x2x0.8

Pulse inputs

Wiring & cables

pay attention to correct polarity!

Synchronous input

Wiring & cables

pay attention to correct polarity!

KBR eBus connection

via RS485

Terminal 90 (⊥)
Terminal 91 (A)
Terminal 92 (B)

Hardware outputs:
Interfaces	Serial interface	RS 485 for connection to the KBR eBus; Max. 32 devices per bus segment, up to 1000 m without a bus amplifier if installed appropriately, for further information see the KBR eBus installation guidelines
Transfer speed	38400 baud
Bus protocol	KBR eBus
KBR eBus addressing	Addressable up to address. 9999 via software, scan mode can be activated on the device
Module bus interface	Serial interface	RS 485 (RJ12) for assembled KBR system cable (6-pole modular cable, not shielded), max. length 30 m when laid appropriately.
Display- und Konfigurationsschnittstelle	Serial interface	RS485 (RJ12)
Relay outputs	Switching steps	5 relays
Switching performance	250 V (AC) / 2A per relay, potential depends on the common connection – not touch-proof
Fault signal relay	Switching performance	250 V (AC) / 2 A potential-free – not safe to touch

Hardware outputs:

Interfaces

Serial interface

RS 485 for connection to the KBR eBus; Max. 32 devices per bus segment, up to 1000 m without a bus amplifier if installed appropriately, for further information see the KBR eBus installation guidelines

Transfer speed

38400 baud

Bus protocol

KBR eBus

KBR eBus addressing

Addressable up to address. 9999 via software, scan mode can be activated on the device

Module bus interface

Serial interface

RS 485 (RJ12) for assembled KBR system cable (6-pole modular cable, not shielded), max. length 30 m when laid appropriately.

Display- und Konfigurationsschnittstelle

Serial interface

RS485 (RJ12)

Relay outputs

Switching steps

5 relays

Switching performance

250 V (AC) / 2A per relay, potential depends on the common connection – not touch-proof

Fault signal relay

Switching performance

250 V (AC) / 2 A potential-free – not safe to touch

Mechanical data:
DIN rail device	Housing dimensions	90 x 106 x 61 mm (H x W x D)
Mounting type	Wall mounting on standard rail 7.5 mm deep, in accordance with DIN EN 50022
Weight	approx. 650g

Mechanical data:

DIN rail device

Housing dimensions

90 x 106 x 61 mm (H x W x D)

Mounting type

Wall mounting on standard rail 7.5 mm deep, in accordance with DIN EN 50022

Weight

approx. 650g

Environmental conditions / electrical safety:
DIN rail device	Standards	DIN EN 60721-3-3/A2: 1997-07; 3K5+3Z11; (IEC721-3-3; 3K5+3Z11)
Operating temperature	K55 (-5°C …. +55°C)
Air humidity	5 % … 95 %, non-condensing
Storage temperature	K55 (-25°C …. +70°C)
Operating height	0…2000 m above sea level
Electrical safety	Standards	DIN EN 61010-1: 2011-07
Protection class	I
Overvoltage category	CAT III
Rated impulse voltage	4 kV
Protection class	Standards	IP20 according to DIN EN 60529: 2014-09
EMC	Standards	DIN EN 61000-6-2:2006-03 + Corrigendum 1:2011-03 DIN EN 61000-6-3:2011-09 + Corrigendum 1:2012-11 DIN EN 61326-1:2013-07

Environmental conditions / electrical safety:

DIN rail device

Standards

DIN EN 60721-3-3/A2: 1997-07; 3K5+3Z11; (IEC721-3-3; 3K5+3Z11)

Operating temperature

K55 (-5°C …. +55°C)

Air humidity

5 % … 95 %, non-condensing

Storage temperature

K55 (-25°C …. +70°C)

Operating height

0…2000 m above sea level

Electrical safety

Standards

DIN EN 61010-1: 2011-07

Protection class

Overvoltage category

CAT III

Rated impulse voltage

4 kV

Protection class

Standards

IP20 according to DIN EN 60529: 2014-09

EMC

Standards

DIN EN 61000-6-2:2006-03 + Corrigendum 1:2011-03
DIN EN 61000-6-3:2011-09 + Corrigendum 1:2012-11
DIN EN 61326-1:2013-07

Power supply:
Power supply	ext. 24 VDC, 1 W, via RJ12 module bus connector

Power supply:

Power supply

ext. 24 VDC, 1 W, via RJ12 module bus connector

Hardware inputs and outputs:
Serial interface	Module bus	RS485 via RJ12 socket
	Baud rate	38400

Hardware inputs and outputs:

Serial interface

Module bus

RS485 via RJ12 socket

Baud rate

38400

Electrical connection:
Module bus – connection	Connecting material	Assembled KBR system cable (modular cable 6-pin, not shielded), max. length 30m when laid appropriately

Electrical connection:

Module bus – connection

Connecting material

Assembled KBR system cable (modular cable 6-pin, not shielded), max. length 30m when laid appropriately

Mechanical data:
Panel device	Housing dimensions	96 x 96 x 46 mm (H x W x D)
Installation cutout	92 x 92 mm
Protection class	Front IP 40
Weight	approx. 175 g

Mechanical data:

Panel device

Housing dimensions

96 x 96 x 46 mm (H x W x D)

Installation cutout

92 x 92 mm

Protection class

Front IP 40

Weight

approx. 175 g

Environmental conditions / electrical safety:
Ambient conditions	Standards	DIN EN 60721-3-3/A2: 1997-07; 3K5+3Z11; (IEC721-3-3; 3K5+3Z11)
Operating temperature	K55 (-5°C …. +55°C)
Air humidity	5 % … 95 %, non-condensing
Storage temperature	K55 (-25°C …. +70°C)
Operating height	0…2000 m above sea level
Electrical safety (in conjunction with the basic device)	Standards	DIN EN 61010-1: 2011-07
Protection class	I
Overvoltage category	CAT III
Rated impulse voltage	4 kV
Protection class	Standards	IP20 according to DIN EN 60529: 2014-09
EMC	Standards	DIN EN 61000-6-2:2006-03 + Corrigendum 1:2011-03 DIN EN 61000-6-3:2011-09 + Corrigendum 1:2012-11 DIN EN 61326-1:2013-07

Environmental conditions / electrical safety:

Ambient conditions

Standards

DIN EN 60721-3-3/A2: 1997-07; 3K5+3Z11; (IEC721-3-3; 3K5+3Z11)

Operating temperature

K55 (-5°C …. +55°C)

Air humidity

5 % … 95 %, non-condensing

Storage temperature

K55 (-25°C …. +70°C)

Operating height

0…2000 m above sea level

Electrical safety (in conjunction with the basic device)

Standards

DIN EN 61010-1: 2011-07

Protection class

Overvoltage category

CAT III

Rated impulse voltage

4 kV

Protection class

Standards

IP20 according to DIN EN 60529: 2014-09

EMC

Standards

DIN EN 61000-6-2:2006-03 + Corrigendum 1:2011-03
DIN EN 61000-6-3:2011-09 + Corrigendum 1:2012-11
DIN EN 61326-1:2013-07

multisio D6

Download

Contact:

Products and solutions:

TÜV certified:

Menu: